- 地址：
- 安國市南陽工業區
- 郵箱：
- 415130881@qq.com
- 電話：
- 18631165157
- 傳真：
- 0312-3427286
- 手機：
- 18631165157
液下渣漿泵的優點都有那些。
液下渣漿泵承如用-49所示，主要用于電廠輸送循環水，也可用于鋼供廠、船
塢排水及農田灌溉等。
液下渣漿泵的優點有:
1)流量大，揚程不高。
2) 體積小，質量輕，機組占地面積小。
3) 效率高，達80% ~ 90%。
4) 起動前不需灌水或抽真空。 5)安全可靠，壽命長。6)汽蝕性能好。
液下渣漿泵的結構特點有:
1)電動機與泵連接(或支撐)方式有兩種:一種是單基礎，電動機和泵靠電動機座合在一起，安裝在一個基礎上; 另一種是雙基礎， 電動機和泵安裝在各自的基礎上。
2)葉片可做成可調式。
3)導軸承材料可以用橡膠、BBF 或賽龍等。
4)軸承用護軸管保護，護軸管內充滿潔凈的壓力水，以潤滑導軸承，防止不干凈的介質進人導軸承造成磨損。
5)泵軸向力和泵本身質量大部分由電動機的推力軸承承受，也可以根據需要設計成泵本身帶推力軸承。
6)泵分為轉子部件(如葉輪、軸、護軸套、導軸承部件、軸封部件等)及導葉體可起抽出的雙殼體結構(見圖5-49)和不可抽出的單殼體結構。
Vertical slurry pump
The vertical slurry pump bearing is shown in Figure - 49. It is mainly used for conveying circulating water in power plants, and can also be used for steel supply plants and ships
Dock drainage and farmland irrigation.
The advantages of vertical slurry pump are:
1) Large flow and low lift.
2) Small size, light weight, small unit area.
3) High efficiency, up to 80% - 90%.
4) No water filling or vacuum pumping is required before starting. 5) Safe and reliable, long service life. 6) Good cavitation performance.
The structural features of the vertical slurry pump include:
1) There are two ways to connect (or support) the motor and the pump: one is a single foundation, and the motor and the pump are combined by the motor seat and installed on the same foundation; The other is double foundation, and the motor and pump are installed on their respective foundations.
2) The blades can be made adjustable.
3) The guide bearing material can be rubber, BBF or Cylon.
4) The bearing is protected by the shaft guard tube, which is filled with clean pressure water to lubricate the guide bearing and prevent the dirty medium from entering the guide bearing and causing wear.
5) The axial force of the pump and the mass of the pump itself are mostly borne by the thrust bearing of the motor, and the pump itself can also be designed with thrust bearing as required.
6) The pump is divided into rotor parts (such as impeller, shaft, shaft sleeve, guide bearing parts, shaft seal parts, etc.) and guide vane body with extractable double shell structure (see Fig. 5-49) and non extractable single shell structure.
上一條：深井泵與渣漿泵如何匹配
